How To Fix A Dryer That Shuts Off Too Soon

How to Fix A Washer That Won’t Spin

How to Fix A Washer That Fills and Drains At The Same Time

Having a faulty appliance in your house can be a pain, especially if you have guests at home or throwing a party. Imagine, your microwave stops working when you have invited your friends. Your routine gets affected and you get tense and tired. Therefore, it is important that you take care of your residential appliance to prevent last minute disasters.

Appliances that you use almost every day are more likely to malfunction. Your refrigerator and washer are two appliances that you use almost every day. When your washer malfunctions, it is best to get help from a washer service technician. This is because your household appliance has several parts that can only be repaired or replaced by a washer technician.

Today, getting a washer repairman to visit your place for washer service or washer repair is easy. All you have to do is give a washer service repair company a call and within no time the washer repair person will be at your place. If you are looking for a good washer repairman near me, all you have do is type “Washer repair near me”, followed by your current residential address, in any search engine. The search engine will display details of all the service providers in your area.

Alternatively, if you plan to repair the washer without professional help, you must identify the parts that are responsible for the problem with your machine. If your washer fills and drains at the same time, here are the parts that could be responsible for the problem.

Water Intel Valve

The inlet valve of your washer is responsible for filling the washtub with hot, warm, or cold water. The working of these valves is controlled by a solenoid which is operated by the electronic control board or the timer. In some washers, the solenoid is also controlled by the pressure or water level switch.

If the water enters the tub during the drain cycle, it could be due to the faulty valve. To check the condition of the valve, disconnect the power supply to the machine when this symptom occurs. If the water continues to enter the tub, it means the inlet valve is defective. On the other hand, if the water stops filling, the problem could be in the switch or electronic circuit board.

Water Level Switch

This switch helps in detecting the correct water level in the washtub. The switch is normally found behind the washer’s control panel. The switch and the tub are usually connected by a dome tube or a hose. When certain water level is reached, the air in the dome tube will push against the diaphragm inside the water level switch. This will turn off the water supply to the tub when the desired water level is reached. If there is a problem with the tube, pressure may not be created to activate the water level switch and water may overflow from the machine.

Before you check the switch, you must check the condition of the dome hose. If it is cracked or worn out, replace it
immediately. At times, the debris inside the dome can prevent the hose from activating the switch. Remove debris from the hose and restart the machine. If your machine does not start even after you have removed the debris or you have replaced the hose, the water level switch may be defective.

You Can Check The Popular Cities We Service Here:

Reno City, Omaha, Albuquerque, Fort Worth, Cleveland, Virginia Beach, Detroit, San Jose, Louisville, Aurora,  Charlotte, Atlanta, San Francisco, Middletown, Seattle, Pittsburgh, San Diego, Austin, Tampa, Dallas, Columbus, Sacramento, Kansas City, Indianapolis, Denver, Nashville, Orlando, Miami, Newark, Little Rock, Tacoma, New York City, Tallahassee, Baltimore, Baton Rouge, Minneapolis, Allentown, Billings, Oklahoma City, Olympia, St. Louis, Colorado Springs, Los Angeles, Jackson, Phoenix, Salt Lake City, Richmond, Silver Spring, Charleston SC, San Antonio, Everett, Tucson, Milwaukee, Philadelphia, Raleigh, Columbia, Las Vegas, Manchester, New Haven, Chicago, Providence, Jacksonville FL, Provo, Henderson, Lakewood, Bowie, Houston Eugene, Birmingham, Boston, Portland

The post How to Fix A Washer That Fills and Drains At The Same Time appeared first on OnSite Appliance

How to Fix A Dishwasher That Won’t Dispense Detergent

How to Fix An Oven That Won’t Program

Oven, stove, and range are an indispensable part of modern kitchens. They make your job in the home kitchen less cumbersome and take less time to cook your favorite dish. However, like any other home appliance even your oven or range could malfunction. Ideally, you should look for a technician that offers household oven repairs. Since repairing the oven requires high voltage test, it is best to allow oven service technician to carry out oven repairs. The oven technician will visit your house at your convenience to troubleshoot the problem with your machine. However, if you don’t plan to use the services of an oven repairman, you must know which part could be responsible for the problem with your machine.

At times, a problem in your oven can affect the programming feature of your residential appliance. Here is a quick guide to help you identify the problem part and service your machine. 

Membrane Switch and Electronic Control Board

In most modern ovens, the programming functions are controlled by the electronic control board. Usually, a problem with the keypad or the membrane switch can prevent you from selecting a program. In some machines, a separate membrane switch is used. In these machines, you may have to only replace the membrane if the keypads don’t work properly. The membrane switch is usually attached to the control board using the ribbon connector. To check the condition of the board and the membrane switch you will need a multi-meter.

Here Are Our Service Areas In These Popular Cities:

Tucson AZ, Orlando, Charlotte NC, Las Vegas, Seattle, Little Rock, Chicago, Denver, Charleston SC, New Haven, Eugene, Portland, Tacoma, San Francisco CA, Phoenix, Detroit, New York City, Providence, Portland, Middletown, Jacksonville, Indianapolis, Omaha, Miami, Everett, Virginia Beach, Boston, Tampa, Columbus, Lakewood, Philadelphia, St. Louis, Newark, Cleveland, Pittsburgh, Reno City, Louisville, San Jose, Birmingham, Atlanta GA, Milwaukee, Oklahoma City, Allentown, Henderson, Bowie, Sacramento, San Diego, Silver Spring, Baton Rouge, Jackson, Houston, Fort Worth, Tallahassee, Los Angeles CA, Kansas City, San Antonio TX, Olympia, Colorado Springs, Minneapolis, Billings, Manchester, Salt Lake City, Raleigh, Albuquerque, Austin, Columbia, Aurora, Dallas, Provo, Baltimore, Richmond, Nashville,

 

The post How to Fix An Oven That Won’t Program appeared first on OnSite Appliance

How To Fix A Dryer That Won’t Shut Off

Most people who have a dryer in their house undermine its importance. They consider it to be not so important home appliance because it has limited use. Only when the residential appliance stops working, they realize how difficult their life can be without it. This is especially true during rainy season and winters, when drying your dirty clothes is a pain.

When you use your dryer regularly during winters, some parts of the household appliance can malfunction. When you face such a situation, don’t PANIC! Your ideal option would be to get help from a dryer service technician. The dryer technician should offer home repairs and if possible must visit your place on the same day. The dryer repairman will be able to visit your home on the same day if you use the services of a local dryer repair company. If you are looking for a good dryer repair near me, you can get help from neighbors, friends and colleagues. You could also use the internet to get these details. Just type “Dryer repair near me” followed by your area code to get a list of companies that offer dryer service repair.

If you plan to repair your dryer without any help from a dryer repair technician, you should know the parts that are faulty. If your machine does not shut off, here are the details of some parts that could be faulty:

Door Switch

Most modern dryers have an in-built safety feature known as the door switch. This switch does not allow the appliance to work when the door is open or not closed properly. If your machine is working when the door is open, it means the door switch is faulty. The door switch is usually fixed behind the front panel of the dryer. Once you locate the switch, you can check its continuity using a multi-meter. If it has more than one terminal, make sure you check the condition of all the terminals. These tests must be performed when there is no power supply to the machine.

Timer

The timer is usually attached to the control console of the dryer. The timer includes a motor that is attached to several parts of the machine. The timer regulates the working of these parts to complete the program selected by the user. If there is a problem in the timer motor or contacts, the dryer will not shut off. When the timer is defective, your only option is to replace the timer. Before replacing the part, make sure you check the condition of the timer using a multi-meter. Of course, this must be done after the machine is unplugged.

Cycling Thermostat

Dryer with Auto Dry feature use a cycling thermostat to advance the timer and regulate the temperature inside your machine. The thermostat controls the timer motor and the heat source to maintain the drum temperature. When checking its condition, make sure there is power supply to and from thermostat. This is a live voltage test and must be done under the supervision of an expert.

Cool Down Thermostat

Some machines have a cool down thermostat that tumbles the clothes with using heat. This usually happens at the end of the drying cycle. The power required to turn the tub is sent to the drive motor through the cool down thermostat. If this thermostat is faulty, it will allow the drum to rotate indefinitely. You can check the condition of the thermostat using a multi-meter, after you disconnect the power supply to the machine.

Locations We Serve in Popular Cities:

Omaha, Virginia Beach, Louisville, Atlanta, San Diego, Columbus, Little Rock, Billings, Oklahoma City, Silver Spring, Everett, Manchester, New Haven, Bowie, Birmingham, Boston, Milwaukee, Pittsburgh, Charleston SC, Allentown, San Antonio, Tacoma, Providence, Houston, Orlando, Miami, Tampa, Richmond, Denver, Eugene, Los Angeles, Las Vegas, St. Louis, Philadelphia, Sacramento, Portland, New York City, Jacksonville FL, Columbia, Fort Worth, Reno City, Seattle, San Francisco, Baton Rouge, Albuquerque, Dallas, Provo, Henderson, Salt Lake City, Aurora, Baltimore, Phoenix, Charlotte, Newark, Indianapolis, Tallahassee, Tucson, San Jose, Raleigh, Jackson, Colorado Springs, Middletown, Chicago, Detroit,  Olympia, Cleveland, Minneapolis, Nashville, Lakewood,  Austin, Kansas City

The post How To Fix A Dryer That Won’t Shut Off appeared first on OnSite Appliance

How To Fix Dishwasher That Won’t Clean Properly

With the advent of dishwasher, cleaning dishes has become easier and less time-consuming. Earlier, we would have to spend several hours cleaning the dirty dishes. Today, all we have to do is put our dishes in the dish washer and let the house appliance do its job. Within a short period, the dishwasher has become an indispensable part of our home. However, like any other residential appliance, even the dishwasher can develop a problem. When your dishwasher malfunctions, it is best to opt for home repairs for dishwasher. You can find details of a dishwasher technician in your area and call them to troubleshoot the problem with your household appliance. The dishwasher service technician will visit your place to repair or service the machine. If you plan to attempt the dishwasher repair yourself, make sure you are aware of the parts that could be responsible for the problem.

At times, your dishwasher may not clean the dishes properly. If you plan to repair the machine without the help of a dishwasher repairman, you should know which part could be responsible for the problem. Here is a brief guide to help you.

Discharge Housing Gasket

If the water pressure from the machine’s spray arm is low, the housing gasket of the upper discharge could be responsible for the problem. The gasket is usually located on the discharge cover just above the impeller. The housing gasket may have got dislocated or may need replacement. If the gasket is damaged and must be replaced, make sure you remove all the debris from the area before installing the new gasket.

Spray Arm

A problem with the machine’s lower spray arm could prevent the home appliance from cleaning the dishes properly. The spray arm is responsible for spraying strong stem of detergent and hot water on the dishes. Before you check the condition of the spray arm, make sure it is able to move freely and is not obstructed by the dirty dishes. At times, the bearing ring of the spray arm may be dislocated or worn out, which can cause the arm to wobble and prevent it spraying water and detergent evenly. If the bearing ring is not worn out or dislocated, you should visually inspect the spray arm for plugged holes or cracks. Food particles, glass, toothpicks, and other debris can clog the holes of the spray, which can impair the direction or force of the spray arm. If there are cracks on the spray arm, it will reduce water force and prevent the machine from cleaning the dishes properly.

Docking Station

Some dishwashers have a middle spray arm which is attached to the machine’s upper rack. In these machines, you must check the docking station and its flappers. The docking station, which has two outlets, provides water to the machine’s middle spray arm. Make sure the docking station is connected properly to the tube that supplies water to the machine. Also, make sure the flappers move freely and close securely to prevent pressure loss when the supply tube of middle spray arm is not inserted.

Chopper

The dishwasher is equipped with a food chopper that is responsible for chopping the leftover food particles into small pieces so that they can be easily drained out from the washer. If the chopper isn’t fine enough or is broken, it can clog the drains. When your washer is not cleaning the dishes properly, you should check the drains. If the drain is clogged by large food particles, you must the check the condition of the chopper.

 

 

 

Water Inlet Valve

A part of the dishwasher that is most likely to fail and prevent the machine from cleaning the dishes properly is the water inlet valve. The valve is located near the lower access panel which is usually in the front of the machine. If water level is not maintained or the machine does not have water, you must first inspect the valve to ensure that power is supplied to the valve when water enters the machine. You can check this using the multi-meter. If there is no problem with the power supply, the valve must be replaced.

Water Delivery Tube

In machines that have upper spray arm, a problem in water delivery tube can prevent the washer from cleaning the dishes properly. The tube is usually made of plastic and it is responsible for supplying water to the upper spray arm. When checking the condition of the tube, make sure it is properly aligned with spray arm and there are no obstructions.

Filters

Most dishwashers are equipped with at least one filter to remove debris from machine during the wash cycle. These filters come with a self-cleaning feature but under detergent use or certain water conditions, it can become clogged. The filter is usually a part of the pump or wash arm assembly. If you suspect that the filter is not doing its job, you should clean the filter. If cleaning does not help, you may have to replace the filter.

Wash Spinner

The wash spinner is a wash arm that is usually on the manifold or on the water feed tube. If the spinner is dislocated or cracked, it could prevent the machine from cleaning the dishes properly.

Detergent Dispenser

A problem with the detergent dispenser could prevent the washer from cleaning the dishes. Ideally, you must use a good quality detergent to wash the dishes. If you use tablets or gel, try switching to powered detergent because it dissolves faster. Some machines have a pre-wash compartment in their detergent cup. You could use this to add detergent to the machine. Also, it is important to use a detergent that suits the local water conditions. For instance, if you use hard water to clean the dishes, you will need more detergent to clean the dishes. However, avoid using too much detergent because it could damage the glassware.

The detergent dispenser may not be working properly because the dispenser cup could be caked or clogged with the old detergent. To troubleshoot this problem, all you have to do is clean the cup. Also, make sure detergent is released by the detergent cup during the wash cycle.

Heating Element

For the washer to clean the dishes properly, a temperature of about 142 degrees Fahrenheit must be maintained. The heating element is used by the washer to maintain the temperature of water inside the machine. It is important to note that when you select the normal wash cycle, the heating element does not play any role in heating the water. So, when you select the normal cycle, make sure the water is hot enough to clean the dishes. Avoid using very hot water to clean the dishes, as it could damage the dishes. Before you start the wash cycle, run the hot water in the sink for 5 to 10 minutes. If the temperature of water drops during the cycle, the heating element could be the culprit. Since the heating element cannot be repaired, you may have to get a replacement.

Pump Impellers

The dishwasher has two impellers – the drain impeller and the wash impeller. These impellers are located inside the dishwasher. The wash impeller is responsible for circulating water inside the machine and pressurizes the water spray arm. The drain impeller is used to drain from the machine. To check the condition of the impellers, you can visually inspect them. If the fins or hub is damaged, you may have to replace it.

Check for the communities that we service in popular cities:

Houston, Las Vegas, Little Rock, Charleston SC, New Haven, Eugene, Tacoma, San Francisco CA, Phoenix, New York City, Portland, Middletown, Aurora, Jacksonville, Omaha, Everett, Boston, Tampa, Lakewood, Philadelphia, St. Louis, Cleveland, Pittsburgh, Reno City, Louisville, San Jose, Birmingham, Atlanta GA, Milwaukee, Oklahoma City, Allentown, Bowie, Sacramento , Baton Rouge, Jackson, Fort Worth, Kansas City, Colorado Springs, Billings, Salt Lake City, Raleigh, Albuquerque, Austin, Columbia, Provo, Baltimore, Nashville, Dallas, Denver, Seattle, Portland, Virginia Beach, Columbus, Detroit, Providence, Orlando, Miami, Olympia, Los Angeles CA, San Antonio TX, Manchester, Tucson AZ, Minneapolis, Newark, Richmond, Henderson, San Diego, Charlotte NC, Chicago, Silver Spring, Indianapolis, Tallahassee

The post How To Fix Dishwasher That Won’t Clean Properly appeared first on OnSite Appliance

How to Fix A Washer With A Burning Smell

Having a washer in our house has not only reduced our workload but has reduced the time we have to spend on cleaning our clothes. However, regular use of the washing machine can wear out a few parts of our household appliance. This can cause the machine to malfunction and upset our daily routine. Ideally, for any problem with your washer you should get help of a local washing machine repair company.

Most local washing machine service companies offer home repairs, wherein, they send an expert washing machine repairman to your place. If you don’t know a good washing machine repair company in your area, you can use the internet to get details of washing machine repair person near me. Just go to any popular search engine and type “washing machine repair near me” followed by your area details. This will give you details of all companies offering washing machine service repair in your area. For most washer problems, it is best to get help from a washing machine service technician.

However, before you call a technician you can identify the problem with your residential appliance. If you experience burning smell during the wash cycle, here is what you could do to identify and troubleshoot the problem.

Spin Belt

In some top loading washing machines, the transmission is driven by the belt. If your washer stops agitating, it could be due to the problem with the belt. To assess the condition of the spin belt, remove the front panel of the machine. After removing the panel, look for the belt at the bottom of your machine. The belt that is damaged will create a noise or cause a burning smell during the wash cycle. If there is no problem with the belt, assess the condition of the drive pulley. You should also assess the condition of the idler assembly before you replace the belt. When replacing the belt, make sure you get the exact replacement of your belt. Before you replace the belt, make sure you switch off the power supply to the machine. 

Pump Belt 

The belt is used to operate the machine’s drain pump. The pump belt is a normal v-shaped belt that attaches the drive motor to the drain pump. Some machines may use an idler pulley to maintain the tension on the pump belt. If you experience burning smell when your machine is operating, you should assess the condition of your pump belt. If the pump belt is damaged or worn out, it is best to get a new belt. When fixing the belt, make sure the pump turns freely when idler pulley is used. Also, check for signs of water or oil leakage on to the belt. All this must be done after power supply to the machine is disconnected. 

Motor Pulley 

The pulley is used by the drive motor to turn the pump and drive belt. It is designed to provide the maximum contact with the pump or drive belt. The belt is usually made of a synthetic material or plastic. When motor pulley is damaged or rusted, it can increase friction and damage the belt. When the drive or pump is not working, you should assess the condition of the motor pulley. If it is corroded or worn out, replace it with the new one immediately. 

Drain Pump 

The pump is used to drain water from the tub during and before the spin cycle. The pump is either motor driven, belt driven, or uses its own motor. If you experience burning smell during or after the wash cycle, it could be because the drain pump is damaged and it cannot turn. If you have a belt driven washer in your home, the burning smell may be due to the belt slipping on to the pulley. For those who have a pump that is driven by its own motor, the burning smell may be due to faulty motor. Before replacing the pump motor, make sure you assess the condition of the inlet, as dust particles can restrict the movement of the impeller.

Pulley Assembly 

Some washers use the assembly to provide tension on the pump or drive belt. When the idler pulley or arm malfunctions, the tension of the belt is not maintained which causes excess friction and slippage. This will cause the belt to overheat and can create a burning smell. If you suspect that pump or drive belt is burnt, you must assess the condition of idler pulley and arm. If you notice rust or signs of wear and tear on the assembly, replace it immediately. 

Motor Coupling 

Some top loading washers use motor coupling instead of a belt to transfer electric power to the transmission from the motor. The coupling connects the drive motor to the transmission. It usually consists of two drive forks made of plastic and a rubber coupling. One fork is attached to the motor shaft and the other connects to the transmission shaft. When the shaft of the machine rotates, the coupling absorbs the pressure and prevents the fork from breaking. If you use the machine regularly, the coupling may wear out and cause the drive flock slip. This can be one of the causes of burning smell. To assess the condition of the coupling and to replace it, you must first get access to it. To do this, you should remove the washer cabinet. Make sure there is no power supply to the machine when you attempt repairs. 

Clutch Assembly

Some washers use the clutch assembly to rotate the washtub. When your clutch is worn out, you can experience burning smell during the wash cycle. You could also hear a scraping sound during the spin cycle when the clutch is worn out. Another symptom of the clutch worn out is the brake shavings or dust found underneath the machine. If your washer displays these symptoms, you must replace the clutch. To replace the clutch, remove the cabinet and the motor assembly. Replacing the clutch assembly is not easy. To do this, it is best to get help from a washing machine technician. 

Spring and Glide 

Some washers use a glide and spring arrangement on the motor for belt tensioning. Normally, the motor is mounted on a solid frame and it uses spring to provide tension. A nylon glide or plastic fixed to the bottom of the motor to allow it to slide on the frame. This allows the pump or drive belt to slip a little when you start the machine and it acts like a clutch. When the glide does not slide properly, the belt gets overheated and may create a burning smell. If you experience burning smell when the motor starts, check the motor pivots, springs, and make sure the base is free of rust or dirt. If you suspect the glides to be defective, you must lubricate or replace them. Also, you may have to replace the belt if it is damaged or burnt.

Here Are Our Service Areas In These Popular Cities:

Summerville

Los Angeles, Louisville, San Diego, Columbus, Billings, Oklahoma City, Silver Spring, New Haven, Bowie, Boston, Milwaukee, Charleston SC, Allentown, San Antonio, Tacoma, Orlando, Miami, Tampa, Richmond, Denver, Las Vegas, St. Louis, Philadelphia, Sacramento, Portland, Columbia, Seattle, San Francisco, Albuquerque, Dallas, Henderson, Baltimore, Charlotte, Indianapolis, Tallahassee, Tucson, San Jose, Raleigh, Jackson, Middletown, Chicago, Cleveland, Nashville, Austin, Kansas City, Portland, New York City, Manchester, Aurora, Salt Lake City, Phoenix, Colorado Springs, Reno City, Fort Worth, Pittsburgh, Olympia, Detroit, Houston, Newark, Baton Rouge, Lakewood, Omaha, Providence, Provo, Everett, Virginia Beach, Jacksonville FL, Minneapolis, Little Rock, Birmingham, Eugene, Atlanta

The post How to Fix A Washer With A Burning Smell appeared first on OnSite Appliance

How To Fix A Dryer That Won’t Tumble

Drying your wet clothes during winters and rainy season can be difficult if you don’t have a dryer in your home. The dryer is an extremely useful appliance. But like any other residential appliance even the dryer could malfunction, which can disrupt your daily routine. In such situations, it is best to get appliance repair help from a professional dryer service technician. Using the services of a dryer repairman will ensure that repairs are carried out properly. Some people avoid using the services of a dryer service technician to reduce expenses. If you are one of those who plan to repair the machine yourself, you must identify the part responsible for the problem. Once you identify the part, all you have to do is replace it with a genuine part.

Having a dryer that does not tumble can be a frustrating experience. To troubleshoot this problem, you must identify the part that can prevent the household appliance from tumbling. Here is a quick dryer repair guide to help you identify the problem part.

Belt

The belt connects the motor to the drum. When the belt rotates, it turns the drum. Regular use of the dryer can wear out the belt. If the dryer is not tumbling, you should check the condition of this belt. Belts that are broken or worn out must be replaced immediately. Ideally, the belt must have grips on both sides and should be flexible. Before changing the worn out belt of your machine, make sure you disconnect the power supply. To replace the belt, you must remove the front panel of the machine.

Pulley Assembly

When you load your clothes in the drum, the belt could slip on the drum or drive pulley. This could damage the drum and other parts of the machine. To prevent this, the idler pulley assembly is to provide tension on the belt. The pulley rotates at very high speeds and over time, it may get damaged due to increased friction. If you hear squealing or squeaking when the drum rotates, it indicates that idler pulley is damaged. If steps are not taken to troubleshoot the problem, the noise will increase and damage other parts of the machine.

Another symptom of a problem with the pulley assembly is the reduced speed of the drum. If the drum of your house appliance does not move or moves very slowly, then you should check the condition of the pulley assembly. To check the condition of the assembly, you must remove the belt. If the pulley turns freely, it means that some other part is responsible for the problem with your machine. Also, visually inspect the condition of the shaft and replace it if it is worn out. The spring tension is responsible for holding the belt tightly. If it is unable to do so, you must replace the spring or the assembly. The shaft and the pulley assembly are usually located near the drive motor. To service these parts, you have to remove both the lower and front panel of your residential appliance.

Maintenance Kit

When you buy a new dryer, make sure you ask the dealer for the maintenance kit that comes with the machine. This kit will contain spare parts that are normally responsible for preventing the dryer from tumbling. Some of the parts that you can find in the kit are bearings, idler pulley, drum rollers, and belts. Once you find the part that is responsible for the problem, just replace it with the one available in the maintenance kit. This will make dryer repair even more economical.

Drive Motor

Both electric and gas dryers use a motor to turn the drum and the blower. When there is a problem with the motor, it will prevent the drum from rotating. It could even produce a humming sound when you use the machine. To service the motor, you have to remove the dryer’s front panel. Before checking the condition of the motor, make sure you check the power supply to the motor. Since this is a live voltage test, it must be performed by a qualified appliance service technician.

Door Switch

The door of most dryers is equipped with a switch that starts tumbling cycle when you close the door. If you don’t hear tumbling sound when the door closes, the door switch could be the culprit. The switch is usually attached to the machine’s front panel. If you suspect that the switch is responsible for the problem, you can check its continuity using a multi-meter. This test must be performed after you disconnect the power supply to the machine.

 

 

Other Service Locations In Popular Cities:

Austin, New Haven, Milwaukee, Charleston SC, Tucson, San Antonio, Orlando, Miami, Las Vegas, Columbia, Henderson, Charlotte, Indianapolis, San Jose, Richmond, Jackson, Chicago, Nashville, Portland, Aurora, Reno City, Olympia, Houston, Lakewood, Providence, Eugene, Tallahassee, Manchester, Raleigh, Allentown, San Diego, Salt Lake City, Cleveland, Everett, Fort Worth, San Francisco, Silver Spring, Detroit, Seattle, Pittsburgh, Philadelphia, Phoenix, Kansas City, Columbus, Oklahoma City, Dallas, Los Angeles, Atlanta, Tacoma, Baltimore, Boston, Provo, Sacramento, Louisville, Baton Rouge, St. Louis, Portland, Jacksonville FL, Austin, Colorado Springs, Albuquerque, Virginia Beach, New York City, Middletown, Billings, Tampa, Denver, Little Rock, Birmingham, Newark, Omaha, Bowie, Minneapolis

The post How To Fix A Dryer That Won’t Tumble appeared first on OnSite Appliance

How To Fix A Refrigerator Door That’s Sweating

A home appliance that works hardest for you is undoubtedly your refrigerator. Any problem with your refrigerator can negatively affect your daily routine. Therefore, it is important to keep your fridge in pristine condition. If you notice water droplets on refrigerator door, you should take steps to troubleshoot the problem with your residential appliance. If you ignore the problem, it can damage other parts of the machine. So, take steps to identify the cause of the problem and take appropriate steps to ensure the fridge repair service is a success. Before you call your refrigerator service technician, you should check the parts that could be responsible for the problem. Here are some parts that could be responsible for the problem.

Door Gasket

When the door seal is damaged, you will notice excess moisture on the shelves of the freezer or on the air outlet ducts. When the gasket is damaged, it can prevent the refrigerator door from closing properly. This will allow air to enter the machine and it may cause defrost issues. If you notice water droplets on the edge of the refrigerator door, it is an indication that gasket is not sealing properly and you must replace it. You can test this by putting a piece of paper at several points along the refrigerator door. Now, close the door normally and try to slide out the paper. If the paper slides out without any problem, it means the gasket is defective and it must be replaced.

Door Assembly

When the assembly is activated, it will dispense ice from the ice maker. The door assembly has a flapper that is spring loaded and has a rubber seal that prevents air from entering the household appliance. Sign of moisture near the dispenser or ice bin area is an indication that the door is not closed properly. To troubleshoot the problem, you must inspect the door assembly. To check the parts of the door assembly, you must remove the cover of the dispenser and inspect its operation. Some parts you must check include door seal, door hinges, and its pivotal mechanism. You must be able to open and close the door without any restriction or binding. If you find any defective part, replace it immediately.

Door Closure Kit

In side-by-side refrigerators, the closer cams assist in closing the refrigerator doors. The closer cams are made of nylon or plastic and they have shoulders that mate together. The door has two cams – one at the top of the door hinge and other on the bottom of the refrigerator door. If either of the closer cams is damaged, the refrigerator door will not close properly. This allows warm air to enter the machine and cause condensation. If the door is not closing properly, check the condition of the cams, and replace them if necessary. When replacing the cams, make sure you get genuine cams from a reputed store. Getting cheap unbranded cams will only damage the machine.

Door Bearing and Hinges

The freezer and fresh food door rotate on hinges. These hinges act as bearing and allow the door to pivot on them easily. Regular use of hinges can make them dry. This can prevent the door from closing properly. Warm air can enter the machine from these gaps and cause moisture problems with the machine. A common symptom of a damaged or faulty bearing is when you hear a thumping or scraping noise when you close or open the door. Worn out hinges must be replaced immediately and make sure you lubricate them using a food safe grease. Lubricating the hinges will reduce friction and increase the durability of the hinges.

If these steps don’t solve the problem, it is best to get help from a professional repairman. To carry out servicing or repairs, the technician will visit your home at your convenience. Before you call a professional, make sure you check the reviews given by customers who used their service. Also, make sure you get an estimate of total repair cost (including the cost of parts) before they carry out repairs. The quality of parts used by the technician has a direct impact on the durability of the machine. Therefore, make sure you check the warranty offer on the parts by the technician.

Here Are Our Service Areas In These Popular Cities:

Las Vegas, Little Rock, New Haven, Eugene, Tacoma, San Francisco CA, Phoenix, New York City, Middletown, Jacksonville, Everett, Boston, Tampa, Lakewood, Philadelphia, St. Louis, Cleveland, San Jose, Birmingham, Milwaukee, Oklahoma City, Allentown, Sacramento , Kansas City, Colorado Springs, Billings, Salt Lake City, Raleigh, Tallahassee, Albuquerque, Austin, Columbia, Provo, Baltimore, Nashville, Dallas, Denver, Seattle, Portland, Virginia Beach, Columbus, Orlando, Miami, Olympia, Los Angeles CA, San Antonio TX, Manchester, Tucson AZ, Minneapolis, Newark, Detroit, Richmond, Baton Rouge, Henderson, San Diego, Charlotte NC, Chicago, Silver Spring, Bowie, Aurora, Indianapolis, Providence, Reno City, Fort Worth, Jackson, Atlanta GA, Louisville, Pittsburgh, Portland, Omaha, Charleston SC, Houston

The post How To Fix A Refrigerator Door That’s Sweating appeared first on OnSite Appliance

How to Fix A Washer That’s Timer Won’t Advance

Not all home appliances are equally useful. We use some residential appliances almost every day, while we use other others occasionally. Appliances such as dishwasher, refrigerator, and washer, are some appliances that we use regularly. Any problem with these appliances can upset our daily routine. For instance, if your washer stops working, you may have to wash a pile of dirty clothes by hand, which is a tiring and time-consuming process. To troubleshoot the problem with your machine, it is best to get help from a repairman who is qualified and experienced in doing washing machine repair. If you feel that there is no major problem with your machine and you don’t require the services of a washer technician, you can try the washer repair yourself. However, make sure you take every possible precaution before you start working on your household appliance.

One of the problems you are likely to encounter when using the washer is the timer not advancing. If you plan to troubleshoot the problem yourself, you should check the parts that could be responsible for this problem and repair or replace the damaged part. Some parts that can be responsible for this problem are:

Lid Switch

Most top loaders come with a safety feature known as the lid switch. This switch is usually located below the top lid of the washer. The switch has a pin or projection attached to it which activates the switch when the lid is closed. The switch supplies power to the motor circuits and the timer. Check if the lid switch is activated when the lid is closed. You must also visually inspect the condition of the actuators and levers and make sure they are not sticking or damaged. If the lid switch is activated but there is no power supply to the circuits and the motor, it means that the switch is damaged and must be replaced. To replace the switch, disconnect the power supply to the machine and remove all the wires that are connected to the switch. Once you remove the switch from the machine, check its condition using a multi-meter. Many people avoid replacing the lid switch that is broken or damaged. You should not do this as it is an important safety feature of the washer and can result in serious injury. Get help with this issue from qualified appliance repair professionals.

Timer Motor

Several functions of the washer are controlled by the timer. The timer has several electrical contacts that are operated by a motor or assembly. Some timer contacts control the functions of the timer motor. If the timer of the machine does not advance, it could be due to a problem with the motor or the timer itself. You can check the condition of the timer using a multi-meter. To do this you must have some knowledge of electrical schematics to determine the correct checks. If the timer is working properly, you must check the continuity of the time motor. If there is a problem with the timer motor, you may have to replace the timer assembly, as timer motor may not be available separately.

Water Level Controller

The controller is responsible for controlling the water valve of the washer. When the desired water level is reached, the controller turns off the valve which prevents water from overflowing. If the desired water level is reached but the machine timer does not advance, it may be due to a defective switch that controls the water level. You will need a multi-meter to check the condition of the switch. Before checking the condition of the water level switch, make sure you disconnect the power supply to the machine. Once you disconnect the power supply, remove all the wires that are connected to the switch. Now check the condition of each contact using a schematic diagram.

Timer Knob

The knob is attached to the machine’s timer shaft. This knob will turn as the timer advances through the wash cycle. The knob can also be used to activate the wash cycle by pulling out on a lever that activates the timer switch. This plastic knob has a metal insert that is attached to the timer shaft. Normal use of the washer can wear out the knob and prevent it from turning with the timer shaft. When the knob is damaged, it will be difficult for the timer to run to the desired wash cycle. Also, it will prevent the dial from turning with the shaft as the wash cycle advances.

If you plan to replace the faulty dial or knob, make sure you remove the power supply to the house appliance. If power supply is not disconnected, you may inadvertently start the washer which can be a serious health hazard. To remove the timer knob from the machine, you may have to move it in and rotate it in an anti-clockwise direction. Some knobs are covered by cap and have a retaining clip that connects it to the dial. In these machines, you have to remove the cap and the retaining clip to remove the knob from the machine.

Drain Pump

The pump is responsible for removing the water from the tub at the end of the rinse and wash cycle. If there is a problem with the drain pump, the water will not drain from the tub and the washer will not advance to the next portion of the cycle. If you face this problem, you must check the condition of the drain pump. Some electronic washers display a fault code when the water does not drain from the tub. You can use this fault code to identify the exact cause of the problem.

Water inlet Valve

During the fill portion of the wash cycle, the inlet valve supplies both hot and cold water to the washer. The valve has two solenoids that are responsible for opening and closing the valve. If there is a problem during the spin cycle or if the machine stalls during the fill portion of wash or rinse cycle, it could be due to the faulty inlet valve. Before you check the condition of the inlet valve, make sure the inlet hose is not blocked or kinked. Also, make sure the inlet screen is clean. If there is no problem with the hose and screens, you can check the continuity of the solenoids using a multi-meter. This check must be done after you disconnect the power supply to the machine. If the solenoids test out OK, you must check the power supply to the solenoids. This washer service requires a live voltage check which should be performed by a trained appliance service technician. If there is no power supply to the solenoids, you must check the components of water level switch, time, lid and cycle selector switch.

Check for the communities that we service in popular cities:

Austin, Charleston SC, Tucson, Jacksonville FL, Orlando, Miami, Henderson, Charlotte, Indianapolis, San Jose, Richmond, Jackson, Chicago, Portland, Aurora, Olympia, Houston, Lakewood, Providence, Eugene, Manchester, Allentown, Salt Lake City, Cleveland, Everett, Fort Worth, San Francisco, Silver Spring, Detroit, Seattle, Pittsburgh, Philadelphia, Phoenix, Columbus, Oklahoma City, Dallas, Los Angeles, Atlanta, Tacoma, Baltimore, Boston, Provo, Sacramento, Louisville, Nashville, Baton Rouge, St. Louis, Raleigh, Portland, Austin, Colorado Springs, Kansas City, Albuquerque, Virginia Beach, New York City, Middletown, Milwaukee, Las Vegas, Billings, Tampa, New Haven, Tallahassee, Denver, San Diego, Little Rock, San Antonio, Birmingham, Reno City, Newark, Columbia, Omaha, Bowie, Minneapolis

The post How to Fix A Washer That’s Timer Won’t Advance appeared first on OnSite Appliance